Xerox XD100 清代碼方法，恢復出廠設置
更新時間：2025/7/19 14:30:14,view:694蘇州施樂打印機售后服務中心客服熱線69616769，蘇州施樂打印機售后維修電話，施樂打印機售后網點，富士dayincanliu,施樂維修視頻2025/6/29
Xerox XD100 清代碼方法，恢復出廠設置
復位方法
reset your WorkCentre and will help to clear error codes.
1. Find the pink Clear button on the Control Panel of the WorkCentre.
2. Find the button below the word Auto.
3. Press these buttons in the following sequence: [Clear], [Auto], [Clear], [Auto]
NOTE: All of the lights on the Control Panel should go out and the LED Display should go blank. If the lights do not go out, then repeat step 3 until they do. It may be necessary to increase or decrease the pace of the [Clear], [Auto], [Clear], [Auto] sequence.
4. Press the [10's] key one time and the [1's] key four times to enter '14' in the LED Display, as if you were to make 14 copies.
5. Press the green [Start] button.
6. Press the pink [Clear] button two times.
7. The WorkCentre should now warm up and come to ready.
8. If the above steps do not clear the error code, repeat steps 3 to 6 a second time.
常見故障問題解答 2011-6-9 9:29:37 施樂XD100數碼復印機，開機后機器自檢轉動，風扇轉動，定影燈亮，但曝光燈一直常亮，并且在2到3公分的距離不停來回運動，大約60秒后曝光燈熄滅，面板出現E7故障代碼，機器無法打印復印。按復印鍵出現15代碼（可能是副代碼）。本人在網上得知XD100與SHARP-AL1240是同類機型，并且得知SHARP-AL1240主代碼：E7，副代碼：15的故障內容：曝光燈斷開；故障詳細情況：曝光燈或曝光燈驅動回路（變換器電路板）不良，曝光燈接觸不良。 但本人已對連接主板到曝光燈的唯一排線作了檢查（正常），鏡頭做了清結，激光頭也做了清結。但現在故障依然存在
常見故障問題解答 2011-6-9 9:30:16 更換曝光燈裝置 , 是變換器電路板壞了
常見故障問題解答 2015-1-14 17:19:05 我的機器xd103f有過這樣的毛病，把上面的玻璃打開，用酒精清潔一下里面的鏡子上的灰塵就可以解決，e7錯誤代碼。
希望您能解決問題。
熱門圖文資料