東芝2008復印機出現：請求維修，C414是怎回事
更新時間：2025/7/12 15:59:59,view:2379東芝打印機2008蘇州東芝打印機售后服務中心客服熱線69616769，蘇州東芝售后電話，東芝售后網點，
東芝2008 復印機出現：請求維修，C414是怎回事
定影壞了。需要維修
東芝常見故障問題解答 龍 2015-8-20 16:40:18
打印機出現請求維修C415是哪里的問題
東芝常見故障問題解答 2015-8-21 6:53:09
定影器不預熱，檢查響應的部件
東芝蘇州維修站 2017/2/18 19:43:57
出現安裝處理單元,原因是把主板電池拔了,還有這個機子前面出現錯誤C414
印了15000業出代碼c414用084000清不掉
檢查定影部件是否異常，如果不是異常的話清除就可以了，08-2002設置為0就可以了
東芝2008 褚樓遍 2018-12-19 Code C414
Description Fuser unit related service call. Thermistor abnormality during warming up or in ready status after abnormality judgment.
Causes MAIN board Thermistors Heater lamp
Remedy
1 Check the power voltage Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?)
2 Check the each elements of error status Check the abnormal thermistors 08-4570-0: Center thermistor 08-4570-1: Side thermistor 08-4570-2: Edge thermistor 08-4570-5: Error counter
3 Check the thermistors
1. Check if the connectors are disconnected.
2. Check if the center and edge thermistors are in contact with the surface of the fuser roller properly?
3. Check if the center and edge thermistors are not deformed or dirty.
4. Check if the harnesses of the center and edge thermistors are open circuited.
4 Check the heater
1. Check if the heater is broken.
2. Check if the connector of the heater is disconnected.
3. Check if the harnesses are connected properly to the terminals of the heater lamp.
4. Check if the thermostat is blown.
5 Check the MAIN board
1. Check if the connectors are disconnected.
2. Check if the conductor pattern on the MAIN board is short circuited or open circuited.
3. Replace the MAIN board.
定影壞了。需要維修
東芝常見故障問題解答 龍 2015-8-20 16:40:18 打印機出現請求維修C415是哪里的問題
東芝常見故障問題解答 2015-8-21 6:53:09 定影器不預熱，檢查響應的部件
東芝蘇州維修站 2017/2/18 19:43:57 出現安裝處理單元,原因是把主板電池拔了,還有這個機子前面出現錯誤C414
印了15000業出代碼c414用084000清不掉
檢查定影部件是否異常，如果不是異常的話清除就可以了，08-2002設置為0就可以了
東芝2008 褚樓遍 2018-12-19 Code C414 Description Fuser unit related service call. Thermistor abnormality during warming up or in ready status after abnormality judgment.
Causes MAIN board Thermistors Heater lamp
Remedy
1 Check the power voltage Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?)
2 Check the each elements of error status Check the abnormal thermistors 08-4570-0: Center thermistor 08-4570-1: Side thermistor 08-4570-2: Edge thermistor 08-4570-5: Error counter
3 Check the thermistors
1. Check if the connectors are disconnected.
2. Check if the center and edge thermistors are in contact with the surface of the fuser roller properly?
3. Check if the center and edge thermistors are not deformed or dirty.
4. Check if the harnesses of the center and edge thermistors are open circuited.
4 Check the heater
1. Check if the heater is broken.
2. Check if the connector of the heater is disconnected.
3. Check if the harnesses are connected properly to the terminals of the heater lamp.
4. Check if the thermostat is blown.
5 Check the MAIN board
1. Check if the connectors are disconnected.
2. Check if the conductor pattern on the MAIN board is short circuited or open circuited.
3. Replace the MAIN board.
熱門圖文