久久婷婷综合色丁香五月,91久久综合一区二区三区桃色,亚欧一区不卡久久,国内永久免费crm系统网站,91九色麻豆,亚偷熟乱区综合一区二区在线,天天日天天色天天操,91精品国产自产91精品资源,欧日美韩视频网站C0m,久久99国产精品片久久99蜜桃,波多野结衣网站,A级无遮挡超级高清在线观看,免费视频91,国精产品一二三区区别在哪,久久无限看,51爱久久网,欧美日韩B区

蘇州hp打印機維修服務網 > 維修資料 > hp > 蘇州HP LaserJet P2035售后維修電話696l6769 > 正文

hp LaserJet P2035常見故障代碼描述,英文手冊

更新時間:2025/6/23 8:57:18,view:162

hp打印機HPLaserJetP2035蘇州hp打印機售后服務中心客服熱線69616769,蘇州hp售后電話,hp售后網點,

Code: -
Display:
Door open
Description:
Opening the cartridge door opens the cartridge door switch (SW301) and disables the 24 V to the high-voltage contacts on the print cartridges.
Remedy:
1. Remove the left cover, and then open and close the cartridge door. Determine if SW301 closes when the door closes. 2. Make sure that the two connectors from the engine control PCA to the switch are securely installed on the switch contacts. 3. Replace SW301 if the message persists.
Code: -
Display:
Install black cartridge
Description:
The product checks for the presence of a print cartridge at start up and anytime the top cover is closed. At start up or when the top cover is closed, a high-voltage bias is placed on the print cartridge's developer roller. This message appears if the print cartridge's antenna is unable to detect the high-voltage bias.
Remedy:
1. Make sure that the sealing tape on the print cartridge has been removed. 2. Verify that the print cartridge is correctly installed. 3. Inspect the high-voltage contact on the print cartridge and in the printcartridge cavity to make sure that they are not damaged. 4. If the messages persists, install another hp print cartridge. 5. Make sure that the engine controller PCA is correctly installed.
Code: -
Display:
Jam in cartridge area
Description:
Photosensors PS913 (media width sensor), PS912 (top of page sensor) and PS915 (fusing assembly exit sensor) detect paper in the cartridge area of the product. If paper arrives at these sensors too early, leaves the sensors too late, or is present at the sensor when not expected, an error message is displayed.
Remedy:
1. Make sure that the paper meets specifications. 2. Open the top cover and remove the print cartridge. Remove any paper or paper fragments present. 3. Lift the registration flap. Make sure sensors PS913 and PS912 move freely. 4. Open the straight-through output door and verify that PS915 moves freely. 5. Make sure that the connector at J203 and J206 on the engine controller PCA are seated.
Code: -
Display:
Jam in output bin
Description:
This error occurs if the duplex reverse photosensor (PS918) or fusing exit sensor (PS915) detect unexpected paper.
Remedy:
1. Make sure that the paper meets specifications. 2. Open the rear duplex jamrelease door and clear any visible paper. Verify the duplex-release sensor flag moves freely. You might need a pen light to observe the flags. 3. Open the face-up output door and the verify the exit sensor flag in the fusing assembly moves freely. You might need a pen light to observe the flag. 4. Verify that the following connectors are seated on the engine controller PCA: . J208 duplex reverse . J206 fusing exit
Code: -
Display:
Jam in Tray 1
Description:
Solenoid (SL1) controls the feeding of paper from Tray 1. When the solenoid is engaged, the Tray 1 pick roller makes one rotation and advances paper into the paper path
Remedy:
1. Inspect the Tray 1 pick roller. Verify the roller is installed correctly and in good condition. 2. Print from Tray 1. Determine if the Tray 1 roller rotates. Listen to determine if the solenoid (SL1) is engaged. 3. Remove the left cover. Determine if solenoid (SL1) is correctly installed. Make sure that the connectors on the solenoid and at J4 of the formatter PCA are seated. 4. If the error persists, replace the solenoid (SL1).
Code: -
Display:
Jam in Tray 2
Description:
Solenoid (SL2) controls the feeding of paper from Tray 1. When the solenoid is engaged, the Tray 1 pick roller makes one rotation and advances paper into the paper path.
Remedy:
1. Inspect the Tray 2 pick roller. Verify the roller is installed correctly and in good condition. 2. Remove Tray 2. Lift the Tray 2 paper present sensor flag while printing from Tray 2. Determine if the Tray 2 roller rotates. Listen to determine if the solenoid (SL2) is engaged. 3. Remove the right cover. Determine if solenoid (SL2) is correctly installed. Make sure that the connectors on the solenoid and at J1104 of the connector PCA are seated. 4. If the error persists, replace the product.
Code: -
Display:
Load paper
Description:
The product did not detect paper in Tray 1 or Tray 2. PS916 detects paper in Tray 1. PS914 detects paper in Tray 2
Remedy:
1. Make sure that paper is loaded in the tray. 2. Make sure that the photosensor flags are not hindered. 3. Make sure that connectors J205 (for Tray 1) and J204 (for Tray 2) on the engine controller PCA are seated.
Code: 10.X
Display:
10.X Supply memory error
Description:
The product has experienced a print cartridge error. The two cartridge memory contacts on the right-rear side of the print cartridge contact the reader contacts on the product.
Remedy:
1. Make sure that a genuine hp print cartridge is installed. 2. When installing the print cartridge, make sure that the memory contacts on the print cartridge and reader contacts on the product make a solid connection. 3. Verify that connector J581 on the engine controller PCA is seated. 4. Replace the print cartridge.
Code: 13.XX
Display:
13.XX Jam in
Description:
The product has detected a jam.
Remedy:
Clear the jam from the location indicated. The job should continue to print. If it does not, try reprinting the job.
Code: 21.X
Display:
21.X Print failure
Description:
The product cannot process the page.
Remedy:
Press OK to continue printing the job, but output might be affected. If the error persists, turn the power off and then on. Resend the print job.
Code: 41.2
Display:
41.2 Engine error
Description:
The product experienced an internal error.
Remedy:
Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize. If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.
Code: 41.3
Display:
41.3 Unexpected size in tray x
Description:
The product has detected print media in the tray that does not
Remedy:
Load the correct media into the tray, or configure the tray for the
Code: 41.X
Display:
41.X.Error
Description:
A temporary printing error has occurred.
Remedy:
1. Make sure that the paper meets specifications. If pages stick together, the paper sensors might detect a sheet of paper longer than expected. 2. Verify that the paper size settings in the control panel, printer driver, and software program match. 3. Verify that the correct paper size is loaded in the product.
Code: 49
Display:
49 Error
Description:
The product experienced an internal error.
Remedy:
Turn the product off, wait at least 30 seconds, and then turn the product on and wait for it to initialize. If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.
Code: 50.X
Display:
50.X Fuser error
Description:
The product has experienced an error with the fuser.
Remedy:
1. Turn the product power off and then on. 2. If you have replaced the fuser, make sure that the correct voltage version is installed (110 V or 220 V). 3. Make sure that the following connectors are seated: . J102 on the engine controller PCA (AC voltage) . J210 on the engine controller PCA (TH1) 4. Replace the fuser
Code: 51.XX
Display:
51.XX Error
Description:
The product has experienced a laser/scanner assembly error.
Remedy:
1. Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize. 2. Make sure that the following connectors are seated: . J1103. . J1. . All connectors on the laser/scanner assembly 3. If all connectors are seated and the error persists, replace the laser/scanner assembly.

Code: 57
Display:
57 Fan error
Description:
The cooling fan (FM1) rotates for approximately 35 seconds at initial start up and during a print job. The fan rotates about 30 seconds after a print job concludes.
Remedy:
1. Turn the product on. Listen to determine if the fan is operating. The fan is located on the upper right-side of the product. 2. Make sure that the fan connector is security connected to J1105 on the connector PCA. 3. Replace the fan.
Code: 59.X
Display:
59.X Error
Description:
A malfunction has been detected with the product's main motor. During normal operation, the main motor should rotate for about six seconds after the product is turned on.
Remedy:
1. Turn the product off and then on. 2. Make sure that connector J202 on the engine controller PCA is seated. 3. If the error persists, replace the main motor
Code: 79
Display:
79 Service error
Description:
An incompatible DIMM is installed.
Remedy:
1. Turn the product power off. 2. Install a DIMM that the product supports. See Parts and diagrams on page 253 for a list of supported DIMMs. See Install memory (hp LaserJet P2050 Series Printers only) on page 64 for DIMM installation instructions. 3. Turn the product on.

熱門圖文

相關資料補充


熱門關注
· hp laserjet p2035n常見故障代碼描述,英文手冊

· hp laserjet p2050常見故障代碼描述,英文手冊

· hp laserjet p2055常見故障代碼描述,英文手冊

· hp laserjet p2055d常見故障代碼描述,英文手冊

· hp laserjet p2055dn常見故障代碼描述,英文手冊

· hp laserjet p2055x常見故障代碼描述,英文手冊

· hp laserjet p3005常見故障代碼描述,英文手冊2

· hp laserjet p3005常見故障代碼描述,英文手冊1

· hp laserjet p3005d常見故障代碼描述,英文手冊1

· hp laserjet p3005d常見故障代碼描述,英文手冊2

· hp laserjet p3005dn常見故障代碼描述,英文手冊2

· hp laserjet p3005dn常見故障代碼描述,英文手冊1

· hp laserjet p3005n常見故障代碼描述,英文手冊1

· hp laserjet p3005n常見故障代碼描述,英文手冊2

· hp laserjet p3005x常見故障代碼描述,英文手冊2

· hp laserjet p3005x常見故障代碼描述,英文手冊1

· hp laserjet p3010 series常見故障代碼描述,英文手冊

· hp laserjet p3015常見故障代碼描述,英文手冊

· hp laserjet p3015d常見故障代碼描述,英文手冊

· hp laserjet p3015dn常見故障代碼描述,英文手冊

· hp laserjet p3015x常見故障代碼描述,英文手冊

· hp laserjet p4014常見故障代碼描述,英文手冊

· hp laserjet p4014dn常見故障代碼描述,英文手冊

· hp laserjet p4014n常見故障代碼描述,英文手冊

· hp laserjet p4015常見故障代碼描述,英文手冊

· hp laserjet p4015dn常見故障代碼描述,英文手冊

· hp laserjet p4015n常見故障代碼描述,英文手冊

· hp laserjet p4015x常見故障代碼描述,英文手冊

· hp laserjet p4515n常見故障代碼描述,英文手冊

· hp laserjet p4515tn常見故障代碼描述,英文手冊

推薦文章
· hpm2727一直初始化

· hpcp5225恢復出廠設置

· hp177fw一體機新機提示安裝成像鼓

· 佳能mf4452報警:e2020002接觸式傳感器hp錯誤,回路故障

· hp2055掃描打印復印一體機,顯示printingdocument然后無反映故障

· hp1005紙剛出定影組件就卡住

· hp2055d開機提示52掃描儀錯誤

· hp128提示文檔進紙器拾取錯誤

· hpm128fp故障燈一直閃控制面板無顯示

· hp126nw提示正在使用用過的碳粉盒

· hpt790繪圖儀錯誤代碼79:03

· 79errorhp2600

· hp176開機時為什么電源燈旁的感嘆號閃爍

· hpm1213nf打印一張通路卡紙

· hp1055cmip地址查詢

· hp-mfpm176n加了粉還提示墨粉量低

· hp3630墨盒加墨水圖解

· hp3035錯誤信息49.ff04

· hplaserjet1100serues顯示感嘆號

· hpm176一直提示三角感嘆號錯誤是怎么回事

· hp1112開機燈閃爍

· hp系統錯誤7904關閉電源如果問題仍存在,請致電hp支持中心

· hpp2055d提示49err3d910c8怎么解決

· hpm1005復印薄的文稿有黑影

· hp226dw提示掃描儀錯誤17關閉然后打開

· hp1280電源燈不亮的真正原因

· hpp1606n不進紙,是什么問題

· hp2025彩色打印機報錯59是哪里的問題

· ricohprintersc680

· hpm128fp開機一直顯示正在初始化

· hp1319f屏幕 無顯

· hp m1005一體機安裝程序錯誤,rpc服務器不可用

· hp m1005 開機報scanner error 20錯誤,故障原因

· hp1020/hp1020plus/hp1010/hp1007定影器故障夾紙?jiān)?/p>

· hp1008打印文稿紙中間有白道,字體模糊?

· hp1005經常夾紙,并且紙夾在定影器處

· hp1213收發不了傳真問題

· hp1025彩色打印機加粉步驟

· hp5200打印白紙,無字問題原因

· hp1025機器偏色校準

· hp5200lx提示13.20.00頂蓋卡紙,解決方案

· hp1536解除密碼方法

· hp1536打印機打印靠右側堅向全白,換硒鼓打印故障以舊

· hp designjet 500 ,800系列打印機 - 打印結束后不裁紙并報錯 6105

· hp t610/t1100顯示要更換裁刀的處理方法

· hp500繪圖儀是打印時每隔10cm就出現一次重影

· hp designjet 500與800打印內容左右有重影

· hp designjet 500 和 800 系列打印機 - 系統錯誤 6105 processing job

· hp designjet 100和110系列繪圖儀報錯誤代碼0113 錯誤代碼

· hp designjet系列繪圖儀打印線條失真如何解決