東芝打印機出現請求維修C413是什么故障?怎樣造成的?
更新時間：2025/7/23 2:51:58,view:345東芝C413蘇州東芝打印機售后服務中心客服熱線69616769，蘇州東芝售后電話，東芝售后網點， 東芝復印機顯示C413, 東芝2505報C413, 東芝2507顯示C413代碼, 東芝2505維修C413問題出在哪里, 東芝2505出現C413,維修視頻
東芝打印機出現請求維修C413是什么故障?怎樣造成的?
東芝413不通電 xjky03 2021/11/13 蘇州東芝413售后維修服務中心地址查詢 Code C413
Description Fuser unit related service call. Thermistor abnormality during warming up, in ready status after abnormality judgment.
Causes MAIN board Thermistors Heater lamp
Remedy
1 Check the power voltage Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?)
2 Check the each elements of error status Check the abnormal thermistors 08-4570-0: Center thermistor 08-4570-1: Side thermistor 08-4570-2: Edge thermistor 08-4570-5: Error counter
3 Check the thermistors
1. Check if the connectors are disconnected.
2. Check if the center,edge thermistors are in contact with the surface of the fuser roller properly?
3. Check if the center,edge thermistors are not deformed, dirty.
4. Check if the harnesses of the center,edge thermistors are open circuited.
4 Check the heater
1. Check if the heater is broken.
2. Check if the connector of the heater is disconnected.
3. Check if the harnesses are connected properly to the terminals of the heater lamp.
4. Check if the thermostat is blown.
5 Check the MAIN board
1. Check if the connectors are disconnected.
2. Check if the conductor pattern on the MAIN board is short circuited, open circuited.
3. Replace the MAIN board.
6 Clear the status counter After repairing the matter which caused the error [C413 / C414], perform the following:
1. Turn ON the power while [0],[8] are pressed simultaneously.
2. Key in "2002", then press [START].
3. Change the current status counter value "1", "2" to "0", then press [OK] (to cancel [C413 / C414]).
4. Turn the power OFF,then back ON. Make sure that the equipment enters the normal ready state.
東芝413不通電 xjky03 2021/11/13 蘇州東芝413售后維修服務中心地址查詢 Code C413 Description Fuser unit related service call. Thermistor abnormality during warming up, in ready status after abnormality judgment.
Causes MAIN board Thermistors Heater lamp
Remedy
1 Check the power voltage Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?)
2 Check the each elements of error status Check the abnormal thermistors 08-4570-0: Center thermistor 08-4570-1: Side thermistor 08-4570-2: Edge thermistor 08-4570-5: Error counter
3 Check the thermistors
1. Check if the connectors are disconnected.
2. Check if the center,edge thermistors are in contact with the surface of the fuser roller properly?
3. Check if the center,edge thermistors are not deformed, dirty.
4. Check if the harnesses of the center,edge thermistors are open circuited.
4 Check the heater
1. Check if the heater is broken.
2. Check if the connector of the heater is disconnected.
3. Check if the harnesses are connected properly to the terminals of the heater lamp.
4. Check if the thermostat is blown.
5 Check the MAIN board
1. Check if the connectors are disconnected.
2. Check if the conductor pattern on the MAIN board is short circuited, open circuited.
3. Replace the MAIN board.
6 Clear the status counter After repairing the matter which caused the error [C413 / C414], perform the following:
1. Turn ON the power while [0],[8] are pressed simultaneously.
2. Key in "2002", then press [START].
3. Change the current status counter value "1", "2" to "0", then press [OK] (to cancel [C413 / C414]).
4. Turn the power OFF,then back ON. Make sure that the equipment enters the normal ready state.
熱門圖文