施樂s2011顯示004345原因

蘇州施樂2011打印機售后服務中心客服熱線69616769，蘇州施樂打印機售后維修電話，施樂打印機售后網點，施樂2011提示換感光鼓,打印有底灰,每次打印都需要把左蓋開關一下才能打印是怎么回事而且還有聲音就像是,打印機提示C-0,怎樣復印身份證,一直在預熱,復印不清楚,富士怎么查看計數,提示010311是什么問題,打印機器不預熱,富士S打印機打印時有延遲,打印復印沒反應,打開側蓋再關上就進紙了什么問題,出現092668,啟動后一直有聲響,2011維修視頻2025/7/22

施樂s2011顯示004345原因 大哥們是什么問題呢，給點指導啥謝謝 蘇州004345 HVPS Communication Error參考 BSD CH9.1ESS/MCU PWB 與 HVPS 之間出現通訊不良。原因 / 處理1. 關閉后再打開電源。2. 關閉電源， 檢查 HVPS J500 到 ESS/MCU PWB J402 之間電線的斷線、 短路或接觸不良。3. 檢查后若無問題， 則依序更換下列零件�！� HVPS (PL18.1)· ESS/MCU PWB (PL18.1)意思是高壓板或主板吧

施樂2011打印重影 davexue 2021/11/27 蘇州施樂2011售后維修服務中心地址查詢

 004-345MCU/HVPS Communication Fail.SOLUTION:
1.Check 5 VDC from P/J 574-5 to P/J 574- 4 on the HVPS Control PWB
2.Disconnect P/J 574.Is there 5 VDC from J 574-5 to J 574-4
3.Check the wire from J411-5 to J574-5 for a short circuit to ground
4.Switch off the power,check these wires for an open, short circuit to ground for the following:
5.HVPS Control PWB P/J574-9 to MCU PWB P/J411-1
6.HVPS Control PWB P/J574-8 to MCU PWB P/J411-2
7.HVPS Control PWB P/J574-7 to MCU PWB P/J411-3
8.HVPS Control PWB P/J574-6 to MCU PWB P/J411-4
9.Check for open circuit, loose connections in the 5 VDC supply wires between P/J411, pins 5,6;,P/J574, pins 5,4.
10.If this does not resolve the problem, replace the HVPS Control PWB & Engine control Board

技術 GUILING17131720 發表于 2024/8/23

側門開關的問題